Material handling systems · Built to your plant layout

Conveyors that fit the plant you already have.

We design, fabricate and commission bulk and unit handling equipment for foundries, cement, food and general engineering plants across India. Every machine is built to your measured layout — not cut down from a catalogue size.

Send your layout See equipment range
1–12Weeks
typical delivery
MS / 304 / 316Materials of
construction
Trial runAt our works
before dispatch
Pan-IndiaSupply, erection
& commissioning
Drawn bySP Dynamics
Unitsmm · kg · TPH
StandardIS · Metric
Projection
First angle
WorksChennai, TN

Start with your industry

Six duty profiles

Handling hot sand is not the same problem as handling bread tins. Pick the plant you run and you will see the equipment we normally build for that duty, in the material grade that survives it.

Foundry & rotary furnace

Charging screw conveyors, hot-sand handling and scrap feed. Built heavy, with abrasion-resistant liners and drives sized for shock loading.

Charging screwSlat chainBucket elevator

Cement & bulk material

Troughed belt, screw and elevator lines for clinker, fly ash, limestone and additives. Dust-sealed casings and takeaway chutes as required.

Troughed beltScrewBucket elevator

Food processing & bakery

SS 304 and SS 316 contact surfaces, wash-down construction, oven and cooling conveyors, and spirals where floor space is short.

Oven conveyorSpiralSS belt

Automotive & engineering

Assembly line slat chain, gravity and powered roller sections, and overhead conveyors for paint and pre-treatment lines.

Slat chainPowered rollerOverhead

Power & thermal

Ash handling screws plus the damper range — butterfly, guillotine and multi-louver — for duct isolation and flow control.

Ash screwGuillotine damperMulti-louver

Warehouse & packaging

Z-type elevating conveyors, gravity roller lines and belt sections for carton, sack and crate movement between floors.

Z-typeGravity rollerFlat belt

Equipment range

Indicative — sized to your duty

The figures below are the bands we normally work within. Send your material, throughput and centre distance and we will confirm the actual sizing on a GA drawing before anything is cut.

EquipmentTypical size bandMaterial of constructionNormally used for
Belt conveyor400–1200 mm widthMS / SS 304Bulk and unit loads, flat or troughed, up to 18° incline
Roller conveyorØ50–Ø114 mm rollerMS / SS 304Gravity or powered lines for cartons, crates and pallets
Screw conveyorØ150–Ø600 mmMS / SS 304 / SS 316Powder and granular feed, including furnace charging duty
Slat chain conveyor3–12 m centresMS / SS 304Assembly lines, hot components, bottle and jar handling
Bucket elevator3–24 m liftMS / SS 304Vertical bulk lift for grain, ash, clinker and minerals
Z-type conveyor1–6 m liftMS / SS 304Elevating small parts and packed goods between levels
Spiral conveyor1–5 m liftSS 304 / SS 316Continuous elevation where floor area is restricted
Oven conveyorTo suit oven widthSS 304 / SS 316Bakery and heat-treatment lines, wire mesh or slat belt
Overhead conveyorTo suit line layoutMSPaint shop, pre-treatment and powder coating lines
Industrial dampersTo suit duct sizeMS / SS 304Butterfly, guillotine and multi-louver isolation and control
Full specifications for all 15 product lines

How a job runs

Enquiry to commissioning

Nothing is fabricated until you have signed the GA drawing. That one step removes most of the surprises that show up at installation.

STEP 1

Layout & duty

You send the material, throughput, centre distance and available floor space. We visit the site if the layout is tight.

STEP 2

GA drawing

We issue a general arrangement drawing with sizing, drive rating and MOC. You approve or mark it up.

STEP 3

Fabrication

Cutting, machining, welding and assembly in our Chennai works, to the approved drawing.

STEP 4

Trial run

The machine is run under no-load at our works. You are welcome to witness it before dispatch.

STEP 5

Erection

Site installation, alignment, electrical hook-up and commissioning, with an AMC option after handover.

What we do in-house

Nothing critical is job-worked out

Fabrication & machining

  • CNC turning — shafts, pulleys, bushesIn-house
  • Plate cutting and formingIn-house
  • MIG / TIG / arc weldingIn-house
  • Screw flight formingIn-house
  • Assembly and no-load trialIn-house

Electricals & controls

  • VFD and starter panelsIn-house
  • PLC programming and HMIIn-house
  • Sensor and interlock wiringIn-house
  • Geared motors and bearingsBought out
  • Belting and chainBought out

Send us your requirement

Tell us the material, the throughput and the distance it has to travel. That is usually enough for us to come back with a budgetary figure within two working days.

spdynamics25@gmail.com

Email
spdynamics25@gmail.com
Works
T-231 A, Sidco Women's Industrial Park
Kattur, Avadi, Chennai – 600 062
GSTIN
33DENPP4793D1Z5

Contact

Chennai, Tamil Nadu

Speak to us

+91 91763 23669

spdynamics25@gmail.com

Eshwar C S

Works & office

T-231 A, Sidco Women's Industrial Park
Kattur, Avadi, Chennai – 600 062
Tamil Nadu, India

GSTIN

33DENPP4793D1Z5

All equipment made to order. Supply, erection and commissioning across India.

Sidco Women’s Industrial Park, Kattur · Avadi, Chennai

Get directions